TECHNICAL ADVICE & FREQUENTLY ASKED QUESTIONS
Envirosystems products are available for purchase Australia wide. We have 2 Trade Centres located in Sydney and Perth, as well as dedicated sales representatives across NSW, VIC, WA and QLD. Our team can also arrange shipping to any location within Australia – just get into contact with us for more information.
Yes, we do! Warranties can be given if they meet our quality requirements, handled and applied in accordance with the correct technical information, installed by an accredited applicator, and inspected by our team. For more information regarding warranties, please contact our team.
Yes, Envirosystems technical team are available to visit you on site to inspect your work and offer project advice. Please note, there may be a fee for this. For more information, contact our team.
Envirosystems ongoingly consults with builders, architects, engineers and relevant industry professionals to deliver optimum system solutions for a variety of project-specific needs. If you are after a particular solution for your project, please contact our team for more information.
PRODUCTS & SOLUTIONS
FAQ - WATERPROOFING
Any area of a building where water can find a way into the structure should be waterproofed. Internal areas of a building that typically require waterproofing include; bathrooms, laundries and kitchens. External areas of a building that typically require waterproofing include; roof tops, basement walls, balconies, planter boxes, podiums, terraces, swimming pools, water features, water tanks, facades. When construction is under the water table, there is also a requirement to ensure that the structure is watertight.
Generally, substrates include concrete, render, fibre cement sheeting, timber, and most masonry surfaces. With that in mind, the list of suitable substrates are not limited to the previously mentioned materials; the selection of an appropriate primer is the key to ensuring compatibility and sufficient adhesion. If your substrate falls outside the list of substrates mentioned, please feel free to contact Envirosystems for further recommendations.
Most structures experience a degree of movement, typically at junctions between floor/wall or wall/wall. To minimise the stress the membrane is exposed to, a bond breaker is used at these junction points prior to the waterproofing membrane application. The bond breaker then prevents the subsequent waterproofing membrane from ‘sticking’ when the membrane is applied over said bond breaker. In accordance with AS3740-2010, a bond breaker must be used at all horizontal/vertical interfaces and across all movement joints where the membrane is bonded to the substrate.
While it may be possible from time to time to waterproof over an existing membrane, it is strongly recommended that any previous membrane is removed in order to ensure the optimum performance of Envirosystems Products.
No. You can use the majority of our products at home without the need for a licensed waterproofer. However, we recommend that the relevant government regulations and Australian Standards are followed: AS 3740 – Internal Wet Areas AS 4654.2 – External Waterproofing Above Ground.
Many of the Envirosystems are DIY friendly, however, we do recommend that you check with the relevant government body in the event that certification is required. If certification is required then a licenced waterproofing contractor will be needed.
While all our products are user-friendly, it is advised that a licensed waterproofer be utilised should there be a question of application ability. Additionally, we strongly recommend that you consult your local certifying body for situations that may require the waterproofing to be undertaken by a licensed professional.
Yes. We have a complete database of licenced waterproofing contractors who are able to assist with your project, please contact us to if you would like recommendations of an applicator in your local area.
FAQ - SEALANTS
A sealant is a product used to seal either:
- The surface of a substrate to improve its serviceability, for example, to prevent excessive water ingress or to dust proof a surface.
- Seal a joint in building components.
A surface sealant, as the name suggests, is typically applied to the surface of a substrate to increase serviceability or improve aesthetics. They work by forming a thin film over the substrate, creating a hard wearing, UV stable, dust proof layer that prevents the excessive ingress of water into a substrate while reducing surface wear at the same time.
A penetrating sealant works by penetrating into the pores of a cementitious or natural stone substrate, to fill the voids with a silicone based compound. This results in a reduction in the absorption capacity of a material, improving its durability and serviceability without altering its aesthetic appearance.
A joint sealant is a flexible polymer mastic (Polyurethane or Polyurea) that is typically used to seal joints where there is anticipated to be a moderate degree of differential substrate movement.
Surface sealants and penetrating sealants can be applied over a variety of porous substrates, but are most commonly applied over cementitious and natural stone substrates.
Joint sealants are able to be applied over a variety of substrates, including concrete, masonry, fibre cement sheet, metal, and timber. Please consult Envirosystems for alternate substrate compatibility.
FAQ - REMEDIAL
There are many reasons why a waterproofing system may fail, in our experience the most common cause of a system failure is due to:
- Incorrect product specification; using the wrong product in the wrong environment.
- Incorrect application methodology; where the product is not applied in accordance with the product datasheet and relevant governing standards.
- Poor substrate preparation; where the product fails due to poor preparation and workmanship.
Envirosystems range of remedial products has been specifically designed to work in the toughest environments with no compromise on performance, giving you the confidence that Envirosystems products will resolve the issue once and for all.
Our range of remedial products includes; moisture tolerant primers, hydrophilic and hydrophobic injection resins, high-performance repair mortars and elastomeric waterproofing membranes.
Whilst our products are DIY friendly, Envirosystems strongly recommends that a licensed contractor is used, due to the highly technical nature of remedial works. This will ensure that your job is done right, without the need for additional remediation.
FAQ - ADHESIVES
An adhesive is used to bond 2 surfaces together such as a tile to the substrate. Envirosystems offer a complete range of cementitious, epoxy and polyurethane adhesives to cover off most adhesion requirements.
Envirosystems offer adhesives that can adhere to most substrates including concrete, render, waterproofing membranes, timber, tiles, FC sheeting etc. For more information on which type of adhesive would be suitable for your project, please contact Envirosystems.
Adhesives can be used whenever there is a need to bond two surfaces/substrates together. Within the building and construction industry, the possibilities are endless with regards to what can be adhered to each other.
Some examples of adhesives with the Envirosystems range include GTA and GTX tiles adhesives which can be used to adhere tiles to the Envirosystems range of waterproofing membranes, Enviro Flex FC which can be used to adhere angles to the floors of internal wet areas (prior to waterproofing) and Enviro Epoxy B-NS when a premium adhesive solution is required.
FAQ - COATINGS
A coating system is a product or combination of products applied over a substrate, to improve its serviceability, durability and overall performance. Often and depending on products being used, this coating will create an impermeable layer to the applied substrate.
Coatings are an essential component of any construction project, they are used in a variety of applications to encapsulate a substrate to improve its serviceability, durability and overall performance. Envirosystems manufacture, and supply a range of coatings that are used for; facades, rooftops, floors and parapet walls.
Envirosystems coating products are available in a range of standards colours, as per the details on their respective Product Data Sheet. For larger order quantities, we may be able to produce a custom colour, please contact the Envirosystems Trade Centre for further information.
FAQ - FLOORING
Envirosystems manufactures a range of flooring products suitable for use in a variety of applications, our products can be used in residential, commercial and industrial environments.
We have a long list of case histories, ranging from; large warehouse spaces, car showrooms, medical facilities, commercial kitchens and aerospace & aviation operations and maintenance facilities.
FAQ - PRIMERS
- To seal the substrate, thus preventing pinhole-ing in the subsequent coat
- To promote adhesion of the subsequent coating